The Elite E15 has six diagram pages on this site: Frame, UNITEC Motor Complete, Gear Box, Filter Block, Fluid Section and Accessories. The fluid section is the largest, at 17 parts, and holds the inlet valve ball, seals, down tube and inlet screen. The gear box holds the pressure control knob, toggle switch and 20 AMP fuse.
The six diagram sections
The Elite E15 is an older electric piston-pump sprayer. Titan's manual for it is numbered 313-348, and it is not one of the PermaStroke sprayers, so the parts here are not the same as on the newer Elite 2000 or 3000. The manual gives a maximum working pressure of 2750 psi, and it says hoses and guns must be rated for at least that. Titan does not give flow or tip figures in the sources we have, so none are quoted here.
Elite E15 diagram pages
| Diagram page | Parts listed | Typical parts |
|---|---|---|
| Frame | 2 | 761-178 flange screw, 0294635 plug |
| UNITEC Motor Complete | 1 | 700-681 motor mount screw |
| Gear Box | 9 | 700-771, 700-646, 710-050, 765-063, 700-680 |
| Filter Block | 10 | 761-451, 730-083, 750-039, 730-222 |
| Fluid Section | 17 | 762-145, 762-073, 761-153, 710-046, 762-175 |
| Accessories | 10 | 700-926, 316-513, 490-032, 0508626 |
Open the page, find the numbered callout and add that part to your cart. The E20 has its own pages with different numbers, so do not order from them for an E15.
Motor and frame
These two pages are short. The frame page lists the 761-178 hexagonal flange screw and the 0294635 plug. The UNITEC motor page lists one part, the 700-681 motor mount screw. If you need something inside the motor itself, it is not on that page, so call (713) 931-0006 with your model and serial number before ordering anything.
Gear box and controls
The gear box page is where the operator controls and the drive parts are. It lists nine parts:
Elite E15 gear box page
The page also lists two plates (700-775 and 702-053), a screw (0509219) and a lock washer (9822113). We list no hour interval for any of these, and Titan's sources that we have do not give one. The 20 AMP fuse is the first thing to check if the sprayer is completely dead and the outlet is known good. Do not confuse the pressure control knob with the pressure-relief/prime knob in the manual: the manual uses that one to relieve pressure by turning it to prime, and the manual is where you confirm the exact steps.
Filter block
The filter block page lists ten parts around the outlet filter. The 761-451 filter housing is the main body, and the 730-083 filter spring sits with it. The 750-039 is listed as the pressure release, and the 730-222 is the outlet cap. The rest are sealing parts: O-rings 761-722, 761-456, 221-008 and 700-499, a gasket 700-881 and a fitting 490-006.
When a filter-block assembly is opened, the O-rings and gasket are the small sealing parts, and a cut or flattened one can leak after reassembly. The diagram does not say how often to replace any of them, and neither do we.
Fluid section
The fluid section is where paint is drawn in and pushed out, and it is the largest page at 17 parts. The ones owners look for most:
- 762-145 inlet valve ball, the valve ball on the page.
- 762-073 outlet valve retainer housing.
- 761-153 down tube and 710-046 inlet screen, the paint-feed side.
- 762-111 seal, 762-103 lower seal and 762-058 seat O-ring.
- 762-175 fluid section repacking kit, and 762-273 piston guide tool.
The remaining parts are housings, screws, an O-ring and a splash guard. Titan does not publish what the repacking kit contains in the sources we have, so confirm that with our parts team before you buy it. The E15 fluid section numbers all start 761 or 762 and they do not match the E20 page, which lists a piston rod and different O-rings.
Accessories
The accessories page lists 700-926 Piston Lube, hoses (316-513, 550-222 and 0291006), the 490-032 swivel union, fittings 490-014, 490-007 and 490-005, the 0508626 pressure gauge and a 2402347 inlet valve pusher housing. That last one is listed on the page, but its catalog fitment names other Elite models and not the E15, so confirm it by phone before ordering. For any hose or gun, check its rating against the 2750 psi in the manual.
Common Elite E15 parts from the diagram pages above:
The Short Version
Start from the section that matches the symptom: gear box for controls and the fuse, filter block for the outlet filter, fluid section for the valves and seals. Manuals are on our manuals page.
Not sure which E15 page has your part?
Call (713) 931-0006 with your model and serial number and our parts team will confirm the part before you order.
(713) 931-0006Order by Parts Diagram