Part 700-680 is a thrust washer used to absorb axial loads and reduce friction between rotating and stationary components in pump and drive assemblies on compatible sprayers. It helps maintain proper clearances and prevents metal-to-metal contact that can cause premature wear. Replacing a worn or damaged thrust washer restores smooth operation and extends the life of the assembly.
| Part Number | 700-680 |
|---|---|
| Part Description | Thrust Washer |
| Brand | Airless / Advantage / Elite / Epic / PowrLiner / Speeflo / ProMark / RentSpray / SprayTech |
| Fits | Airless Sprayer 330, 440XC, 550XC, 660XC, 690GXC, 1100XC, 1200GXC; Advantage GPX 85; Elite E15, E20, G55, G40; Epic 447EX, 447HPX, 660EX, 660HPX, 690GX, 1200HPG; PowrLiner 2850, 2800, 3100; Speeflo PowrLiner 1800M / 2800M; ProMark II (759-2010); RentSpray 700; SprayTech GPX85 |
| Condition | New |
The 700-680 Thrust Washer is a precision component designed to handle axial thrust loads within pump and drive assemblies. Positioned between rotating and stationary parts, it absorbs end-play forces, reduces friction, and maintains critical clearances. This helps prevent metal-to-metal contact that would otherwise lead to rapid wear, heat generation, and eventual component failure.
Over time, thrust washers can wear thin, become scored, or develop grooves from constant pressure and contamination. A worn thrust washer may allow excessive end-play, causing noise, vibration, reduced efficiency, and accelerated wear of adjacent components such as gears, bearings, or housings. Replacing with genuine part 700-680 restores proper clearances and smooth operation.
| Axial load absorption | Handles thrust forces from rotating components |
|---|---|
| Friction reduction | Provides a low-friction surface between moving parts |
| Clearance maintenance | Maintains proper end-play and alignment |
| Visible wear | Thinning, scoring, or grooving on the washer surface |
|---|---|
| Excessive end-play | Noticeable axial movement in shafts or gears |
| Noise / vibration | Unusual sounds from excessive clearance |
| During overhaul | Replace proactively when rebuilding pump or drive assemblies |
Part 700-680 is used across a wide range of sprayer models. Always confirm fitment using the correct parts manual for your specific machine.
| Brand / Series | Model |
|---|---|
| Airless Sprayer | 330 |
| Airless Sprayer | 440XC |
| Airless Sprayer | 550XC |
| Airless Sprayer | 660XC |
| Airless Sprayer | 690GXC |
| Airless Sprayer | 1100XC |
| Airless Sprayer | 1200GXC |
| Advantage | GPX 85 |
| Elite | E15 |
| Elite | E20 |
| Elite | G55 |
| Elite | G40 |
| Epic | 447EX |
| Epic | 447HPX |
| Epic | 660EX |
| Epic | 660HPX |
| Epic | 690GX |
| Epic | 1200HPG |
| PowrLiner | 2850 |
| Speeflo PowrLiner | 1800M |
| Speeflo PowrLiner | 2800M |
| PowrLiner | 2800 |
| PowrLiner | 3100 |
| ProMark II | 759-2010 |
| RentSpray | 700 |
| SprayTech | GPX85 |
When replacing thrust washers, inspect these associated components to ensure a complete repair.
Check for wear or damage; replace if rough or noisy.
Inspect mating surfaces for scoring or wear.
Replace if leaking or damaged to prevent contamination.
Copyright © 2024 AlltitanParts.com - All Rights Reserved.
