Titan lists the PowrBeast 9700 for up to five guns at 3.0 gpm, and the maximum tip size falls as guns are added: 0.055 in. for one, 0.039 for two, 0.031 for three, 0.027 for four and 0.023 for five. The 9700 accessories diagram lists 2-gun manifolds, 3300 psi hoses, guns and a pressure gauge. Keep every component at or above the system rating.
A multi-gun job asks one pump to feed several people at once, so the planning is different from a single-gun setup. The two questions that matter are how big a tip each gun can take, and whether every hose, gun and fitting downstream is rated for the pressure the sprayer can produce. This guide answers both for the PowrBeast 9700, using Titan's published figures and the accessories on the site's 9700 diagram. It is a planning aid. The hookup itself, and the order of setup and shut-down, belong to your manual.
What Titan lists for the 9700
Titan's published figures for the gas PowrBeast 9700 are a maximum delivery of 3.0 gpm, a maximum operating pressure of 3300 psi, a Honda GX270 engine, and a capacity of up to five guns. That is the highest gun count Titan lists for any PowrBeast. The unit part is 0537007, which the site sells as the PowrBeast 9700 (Honda). It comes with an RX-Pro gun, a 517 TR1 reversible tip and a 1/4 in. x 50 ft airless hose, so a second gun and anything beyond that is yours to add.
The five-gun figure is a ceiling on what the pump can feed, not a target. Whether your crew should run five guns depends on the tips, the coating and the job, none of which this page can judge for you.
Tip limit as you add guns
PowrBeast 9700 maximum tip size by number of guns (Titan's listed figures)
| Guns running | Maximum tip |
|---|---|
| 1 | 0.055" |
| 2 | 0.039" |
| 3 | 0.031" |
| 4 | 0.027" |
| 5 | 0.023" |
These are upper limits, not recommendations. A tip at the limit uses all the delivery the table allows for that gun count; the right tip for your coating can be smaller.
The limit falls because the pump's delivery is shared. One pump produces a fixed maximum flow, and each additional gun takes a share of it. A tip opening large enough for one gun would starve the others if all guns were using it, and pressure at the tips would fall. Staying at or under the table is how you keep the whole set spraying properly.
Two reminders from general airless practice apply to every gun on the manifold. The orifice size sets how much material that gun delivers, and the fan angle sets the pattern width. And a worn tip has a wider orifice, so it passes more paint than its marking says. On a multi-gun setup that matters twice, because one worn tip draws flow away from the guns beside it. Replace any tip whose pattern turns coarse or streaky. The 661-020 tip seat and seal kit comes as a 5 pack, and the 0289228 tip guard is the part to fit on every gun.
Manifolds on the diagram
The Powrbeast 9700 (Gas) Accessories page lists two manifold numbers, both named 2-Gun Manifold with ball valves: 975-212 and 975-312. The name tells you what each one splits the flow between. The listings do not say how the two numbers differ, so call (713) 931-0006 with your model and serial number before choosing between them.
We are not going to describe how to plug a manifold into the sprayer or into a hose run. Connecting several guns to a pressure source is the part of the job where a mistake can mean a failed fitting at 3300 psi, and the right method is in the PowrBeast manual on our manuals page. Use the manual's pressure relief procedure every time you add or remove a gun from the setup.
Hose and gauge
Airless systems are only as strong as their lowest-rated part. The sprayer's maximum operating pressure is 3300 psi, so every hose, whip hose, gun, fitting and extension on a manifold has to be rated for at least that. Check the markings on anything you are adding, including parts you already own. The 9700 accessories diagram lists these hoses and fittings:
- 0291006, a 3300 psi hose, 50 ft x 3/8 in. The listing says it replaces Titan 690-375-50.
- 316-506, a 3300 psi whip hose, 5 ft x 3/16 in., the short flexible length at the gun.
- 316-505, a 50 ft spray hose. The listing does not state a pressure rating, so check the hose's own marking against 3300 psi before you add it to a multi-gun set.
- 05045, a fitting, 1/4 in. x 1/4 in.
We do not give a maximum hose length for the 9700, because Titan does not publish one in the sources we use. Longer runs and many guns both change how a setup behaves, so follow the manual for hose sizing rather than guessing from a table here.
The 0508239 high pressure fluid gauge is also on the diagram. On a setup with several guns it gives you a reading to compare against instead of working by feel, which helps when something changes and you want to know whether it is the pump or one of the guns.
Guns and extensions
The same 9700 accessories page lists several guns. The one that ships with the unit is the 0538020 RX-Pro airless gun with the 517 TR1 tip. Others on the page include the 0538070 RX-APEX non-filtered gun, the 0538005 RX-80, the 550-250 S-3 swivel gun and the 0289013 M-4 gun. Grip kits are listed in small (0538217), medium (0538218) and large (0538219).
For reach, the page lists gun extensions in three lengths, 2418850 at 10 in., 2418851 at 20 in. and 2418852 at 30 in., a 3 ft pole extension with swivel and guard (2437218), and the 651-070 six inch tip extension with guard. Every extension is another pressure-rated part in the line, so apply the same check as for hoses. The RX-APEX is listed as non-filtered, so if you choose it, plan your filtering elsewhere in the system. The 0089959 filter is a gun filter the accessories page lists.
A checklist before you add guns
Count the guns and read the table
Find your gun count in the tip table above and confirm no tip is larger than the limit for that count. With five guns the limit is 0.023 in.
Check every rating
Read the pressure marking on each hose, whip hose, gun and extension. Anything below 3300 psi stays out of the setup.
Look at the tips
Replace any tip with a coarse or streaky pattern before the job, not during it. A worn tip changes what the other guns receive.
Check the pump end
A multi-gun job asks more of the filters and fluid section. Open the 9700 Main Assembly I page to see the 0537256 fluid section assembly and the filter assembly if anything looks off.
Ask before you order manifolds
Call (713) 931-0006 with your model and serial number if you are unsure which manifold number you need or how it fits your layout. The full PowrBeast diagram list starts at PowrBeast Gas & Electric Sprayer Parts.
Parts mentioned in this guide:
−12%
−23%
The Short Version
Titan lists the 9700 for up to five guns, with the maximum tip dropping from 0.055 in. for one gun to 0.023 in. for five. Add the manifolds, hoses and guns from the 9700 accessories page, check that everything is rated for 3300 psi, and get the connection method from the manual.
Planning a multi-gun setup?
Call (713) 931-0006 with your PowrBeast model and serial number and our parts team will help match manifolds, hoses and guns.
(713) 931-0006Order by Parts Diagram