Titan 0289228 Tip Guard, G-THREAD
Replace a worn or damaged spray tip guard with the Titan 0289228 Tip Guard, G-THREAD. Designed for compatible Titan spray gun and tip assemblies using the specified G-thread connection, this accessory helps position the spray tip at the gun outlet and provides a protective guard around the spray area. The correct guard is important for secure installation and proper tip alignment. Order part 0289228 when your equipment documentation identifies this G-thread tip guard. Verify the gun model, thread specification, compatible spray tip, and required seals before purchasing. Never operate an airless spray gun without the manufacturer-approved tip guard installed.
Purpose: Supports proper spray tip installation and guarding.
Application: Compatible Titan spray gun assemblies.
Selection: Confirm G-thread connection and spray tip compatibility.
Safety and Fitment Note: G-thread compatibility must be verified against the exact spray gun and tip system. The tip guard does not eliminate the risk of high-pressure fluid injection. Always follow Titan's spray gun safety and pressure-relief instructions.
Replace Your Spray Tip Guard with Titan 0289228 Tip Guard, G-THREAD
Maintain a properly guarded spray gun with the Titan 0289228 Tip Guard, G-THREAD, a replacement accessory for compatible airless spray gun and reversible-tip assemblies. Also identified in Titan accessory literature as the 7/8-inch No Build Guard, part 0289228 features an aerodynamic dimple design intended to improve airflow and reduce paint accumulation around the guard. Its large seal-cavity flats assist with seal installation, while its design permits guard rotation without loosening the connection to the gun. Titan rates this guard for a maximum working pressure of 5,000 PSI (34.5 MPa). AllTitanParts lists the guard for selected G-10, LX 80 II, S5, Elite, Impact, PowrBeast, and PowrLiner equipment. Confirm the exact spray gun, 7/8-inch interface, tip family, seal arrangement, and system pressure before ordering.
Titan 0289228 Tip Guard, G-THREAD Compatible Models
AllTitanParts identifies the following spray guns and equipment as applications for part 0289228. The installed spray gun, not the sprayer model alone, determines the correct guard interface and tip system.
Titan Airless Spray Guns
G-10, LX 80 II Stripe, LX 80 II, and S5. The S5 and G-10 parts diagrams directly list Titan 0289228. The RX-Pro gun parts catalog also identifies this guard.
Titan Elite Sprayers
Elite 3500, Elite 3500 72V, and Elite 5500. Verify the installed spray gun and tip assembly before replacing the guard.
Titan Impact Sprayers
Impact 340, Impact 400, Impact 410, Impact 440, Impact 540, and Impact 1640. These are catalog-listed equipment applications; guard compatibility depends on the fitted gun.
Titan PowrBeast Sprayers
PowrBeast 4700, PowrBeast 4700T, PowrBeast 7700, and PowrBeast 9700. Confirm that the guard's 5,000 PSI maximum rating is appropriate for the complete spray system.
Titan PowrLiner Equipment
PowrLiner 550, 2850, 3000, 3500S, 3500 72V, 4500, 4955, 5500, 6955, and 8955. Confirm the spray gun's actual guard and tip specifications before ordering.
Important: Equipment catalog listings do not establish that every factory or replacement gun on these machines uses the same tip guard. Check the exact gun model, tip system, and required pressure rating.
What Does the Titan 0289228 Tip Guard Do?
The tip guard is installed at the front of a compatible airless spray gun, surrounding the spray tip. Its primary purpose is to provide a physical guard around the high-pressure spray area and support the approved spray tip assembly.
Titan's No Build Guard design incorporates aerodynamic dimples intended to improve airflow and reduce paint accumulation around the guard during spraying. This can make routine cleaning easier and help keep the guard free from excessive coating buildup.
The guard's seal cavity also includes large flats intended to simplify installation of the appropriate seal. The ability to rotate the guard without loosening its connection helps with positioning during use.
Safety Limitation: A tip guard reduces opportunities for accidental contact with the spray area but cannot prevent every injection injury. Never point a spray gun toward yourself or another person, even when the guard is installed.
When Should You Replace the Titan Tip Guard?
Cracked or broken guard: Replace a guard that has lost structural integrity.
Bent or distorted housing: Physical damage can affect guard positioning and protection.
Damaged mounting threads: Replace a guard that cannot be secured correctly to the spray gun.
Missing guard: Do not operate the gun until the correct guard has been installed.
Damaged seal cavity: Inspect the guard if the tip seal cannot be installed or seated correctly.
Paint buildup: Clean accumulated coating using approved procedures. Replace the guard if damage or permanent obstruction prevents proper use.
How to Replace Titan 0289228 Tip Guard, G-THREAD
High-Pressure Safety Warning: Airless spray equipment can cause serious injection injuries. Before removing a guard or tip, switch off the sprayer, engage the gun trigger lock, and follow the complete manufacturer pressure-relief procedure.
Step 1: Identify the spray gun. Confirm the exact gun model and manufacturer-specified tip guard part number.
Step 2: Verify the connection. Check that the gun outlet and Titan 0289228 guard use compatible 7/8-inch connections.
Step 3: Check the pressure rating. Ensure the complete system will operate within the lowest maximum pressure rating of its components, including the guard's 5,000 PSI limit.
Step 4: Relieve system pressure. Follow the spray gun and sprayer manuals before handling the tip assembly.
Step 5: Remove the old guard. Follow the manufacturer's removal instructions and avoid damaging the gun outlet threads.
Step 6: Inspect the tip and seal. Examine the spray tip, seat, retainer, and seal for wear, damage, or contamination.
Step 7: Install the correct seal arrangement. Use the tip seal or seat specified for the installed gun and tip system.
Step 8: Attach the new guard. Install Titan 0289228 according to the gun manufacturer's instructions without cross-threading or forcing the connection.
Step 9: Confirm positioning. Verify that the guard and spray tip are correctly seated, oriented, and secure.
Step 10: Test safely. Restore pressure according to the sprayer manual and inspect for leakage without placing hands near the spray tip or fluid stream.
Titan 0289228 vs. Other Titan Tip Guards
Titan offers different guard designs for different spray gun, tip, and pressure requirements. Do not substitute one guard solely because its connection appears similar.
Selection Note: A higher guard pressure rating does not increase the maximum operating pressure of the spray gun, hose, tip, or sprayer.
Related Titan Spray Tip Guard and Gun Parts
Inspect the following components when replacing the Titan 0289228 Tip Guard, G-THREAD.
Related parts are sold separately unless a specific listing states otherwise. Verify the gun and tip assembly before selecting replacement seals or accessories.
Find Compatible Titan Spray Gun and Tip Guard Parts
Use these AllTitanParts catalogs to identify Titan 0289228 and its associated gun components.
Frequently Asked Questions
Answers about Titan 0289228 Tip Guard, G-THREAD compatibility, pressure rating, and replacement.
What is Titan 0289228 Tip Guard, G-THREAD?
It is a replacement spray tip guard for compatible airless spray guns. Titan also identifies part 0289228 as its 7/8-inch No Build Guard.
What is the maximum pressure rating of Titan 0289228?
Titan identifies a maximum working pressure of 5,000 PSI (34.5 MPa). The complete spraying system must remain within the rating of its lowest-rated component.
Does Titan 0289228 fit the Titan S5 spray gun?
Yes. The AllTitanParts Titan S5 spray gun parts diagram lists part 0289228 as the tip guard.
Is Titan 0289228 compatible with the G-10 spray gun?
Yes. The G-10 High Capacity Spray Gun parts catalog lists Titan 0289228.
Can I use Titan 0289228 with RX-Pro?
The RX-Pro gun parts catalog lists 0289228. Confirm the specific tip and seal arrangement before installation.
Does Titan 0289228 fit every Titan sprayer?
No. Compatibility depends on the installed spray gun, its guard interface, the tip family, required seal, and maximum operating pressure.
What is the difference between Titan 0289228 and 661-027?
Titan 0289228 is the 5,000 PSI No Build Guard. Titan 661-027 is a separate High Pressure Tip Guard rated for 7,700 PSI. The two should not be treated as universally interchangeable.
Does the Titan 0289228 guard include a spray tip?
A spray tip is not confirmed as included with part 0289228. Treat the spray tip and required seals as separate items unless the product packaging specifies otherwise.
Can I spray without a tip guard?
No. Always use the manufacturer-approved tip guard. The guard reduces accidental contact risk but does not eliminate the danger of high-pressure injection injuries.
Where can I buy Titan 0289228 Tip Guard, G-THREAD?
Order the Titan 0289228 Tip Guard, G-THREAD from AllTitanParts after confirming gun and tip compatibility.
No reviews yet. Be the first to review this product!