Titan 661-020 Tip Seat and Seal Kit (5 Pack)
Maintain a properly sealed spray tip connection with the Titan 661-020 Tip Seat and Seal Kit (5 Pack). This replacement kit provides seat-and-seal components for servicing compatible Titan airless spray tip and guard assemblies. It is a practical maintenance option when existing sealing components become worn, damaged, misplaced, or unable to maintain the intended connection at the spray gun outlet.
Compatibility: Confirm Titan 661-020 against the specified spray tip, guard, and spray gun parts documentation.
A convenient five-pack for replacing service-worn tip sealing components. Inspect the spray tip, guard, and mating surfaces before installation to identify other possible sources of leakage.
Restore Your Spray Tip Seal with the Titan 661-020 5-Pack Kit
Keep your compatible Titan spray tip assembly properly sealed with the Titan 661-020 Tip Seat and Seal Kit (5 Pack). Also identified in Titan accessories documentation as a solvent-resistant seal and retainer kit, this maintenance pack provides replacement sealing components for specified No Build and High Pressure spray tip guard configurations. Whether you are servicing a leaking tip connection or preparing spare parts for routine maintenance, the five-pack offers a convenient way to keep the correct sealing hardware available.
How the Titan 661-020 Tip Seat and Seal Kit Works
The spray tip sealing arrangement helps prevent pressurized coating material from escaping around the connection between the spray tip and its guard assembly. The seal and retainer must be correctly matched and installed to provide the intended sealing interface.
Over time, repeated tip changes, material exposure, compression, and normal service conditions can affect the condition of sealing components. Replacing a damaged seal-and-retainer set with the manufacturer-specified parts can help restore the proper assembly configuration and address leakage caused by defective sealing hardware.
Why Keep the Titan 661-020 Five-Pack Available?
Keep replacement sealing hardware available when servicing compatible spray tip assemblies.
Replace defective tip sealing components without unnecessarily replacing the complete spray gun.
A useful purchasing configuration for workshops, contractors, and routine equipment maintenance.
Signs Your Spray Tip Seat and Seal May Need Replacement
Inspect the sealing components when you notice:
- Coating material leaking around the spray tip or guard connection.
- Visible cracks, flattening, cuts, or deformation of the existing seal.
- A missing, damaged, or incorrectly positioned retainer.
- A tip connection that cannot be assembled correctly using the specified components.
- Persistent leakage after the tip and guard have been inspected and correctly installed.
An irregular spray pattern can also result from a worn tip, clogged filter, unsuitable coating, or incorrect pressure setting. Diagnose the complete spray tip assembly before selecting replacement parts.
Titan 661-020 is identified for specified No Build and High Pressure tip guard arrangements. A sprayer model appearing in an accessories catalog does not mean every spray gun or tip guard used with that machine accepts this kit. Match the installed gun, guard, tip family, and required seal-and-retainer part number before ordering. Do not substitute 661-020 for an HEA-specific tip seal without documented compatibility.
Shop Titan Tip Seals and Related Replacement Parts
Find the correct seal-and-retainer kit, tip guard, or spray tip component for your Titan airless spraying equipment.
Related categories are provided for parts identification and comparison. Confirm individual component compatibility before purchasing.
Installation and Safety Guidance
Before removing the spray tip, guard, or sealing components, turn off the sprayer and follow the complete pressure-relief procedure in the manufacturer's operating manual. Engage the spray gun trigger lock and disconnect the equipment from its power source as instructed.
Remove the existing seal and retainer according to the applicable tip guard instructions. Inspect the mating surfaces and confirm that the replacement components match the required configuration. Install the new parts in the manufacturer's specified orientation and sequence.
Reassemble the tip and guard correctly before testing. Never operate the gun with missing sealing hardware or a damaged guard. Keep hands and other body parts away from high-pressure spray outlets. A suspected fluid-injection injury requires immediate emergency medical attention.
Frequently Asked Questions
Answers to common questions about Titan 661-020 compatibility, sealing performance, and maintenance.
What is Titan 661-020 Tip Seat and Seal Kit?
Titan 661-020 is a five-pack seal-and-retainer maintenance kit for specified spray tip guard assemblies. Titan accessories documentation identifies it as a solvent-resistant seal and retainer kit.
How many replacement sets are included?
The product is sold as a five-pack of seal-and-retainer service sets.
Which Titan spray tip guards use part 661-020?
Titan identifies the kit for specified No Build and High Pressure tip guard configurations. Confirm the installed guard and tip family using the manufacturer's parts documentation.
Does Titan 661-020 fit every Titan Impact or PowrLiner sprayer?
No universal fitment should be assumed. Compatibility depends on the installed spray gun, tip guard, and sealing arrangement rather than the sprayer model alone.
Is Titan 661-020 solvent resistant?
Yes. Titan accessories documentation describes 661-020 as a solvent-resistant seal and retainer kit. Always confirm the intended coating and cleaning solvent are approved for the complete spray gun assembly.
What is the difference between Titan 661-020 and 661-021?
Titan 661-020 is a five-pack solvent-resistant seal-and-retainer kit. Titan 661-021 is listed as a six-pack of white solvent-resistant seals. They have different purchasing configurations and should not be treated as interchangeable without checking the required assembly.
Can worn tip seals cause paint leakage?
Yes. Damaged, flattened, or incorrectly installed seals can allow coating material to escape around the spray tip connection. Inspect the guard, retainer, and mating surfaces as well.
Where can I buy Titan 661-020 Tip Seat and Seal Kit?
You can order the Titan 661-020 Tip Seat and Seal Kit (5 Pack) from AllTitanParts. Check the correct tip guard and sealing configuration before purchasing.
No reviews yet. Be the first to review this product!