Titan PowrCoat 730 Gun Manifold Assemblies Parts

Shop verified components for the PowrCoat 730 Gun Manifold Assemblies, including the 1/4-inch and 3/8-inch hex nipples, matching ball valves, outlet fittings, pipe plug, and 970-100 manifold block. Use the official single-gun or multiple-gun configuration, thread-size column, item number, and exact Titan part number before ordering.

Verified Optional Diagram

Match six numbered positions across single- and multiple-gun layouts.

1/4-Inch and 3/8-Inch Paths

Choose the correct nipple, valve, and outlet fitting family.

Independent Gun Control

Service branch shutoff, distribution, outlet connection, and unused-port closure.

Diagnose Each Branch

Check the valve, fittings, hose, gun, tip, threads, and manifold port first.

Assembly Overview

How the PowrCoat Gun Manifold Distributes Coating to Multiple Guns

This page is an exploded optional gun-manifold assemblies parts category for PowrCoat equipment, including the PowrCoat 730. Titan documents single-gun assemblies 975-111 and 975-311, add-a-gun kits 975-200 and 975-300, and complete two-, three-, and four-gun manifolds in 1/4-inch and 3/8-inch configurations.

Pressurized coating enters through the selected inlet nipple and reaches the 970-100 manifold block. Each active branch uses the correct ball valve and outlet fitting to supply a gun hose. Unused ports are sealed with the specified 227-033 pipe plug.

Main Functions

Functions Supported by the Gun Manifold Assemblies

Distributes pressurized coating from one supply into multiple gun branches.
Provides individual branch shutoff through the documented ball valves.
Connects high-pressure hoses through the correct outlet fittings.
Expands an existing setup with documented add-a-gun configurations.
Seals unused manifold ports with the specified pipe plug.

Service Applications

When Contractors Use This Manifold Parts Diagram

One gun branch has low, intermittent, or no coating flow.
A ball valve will not open, close, or isolate its gun line.
Fluid leaks at a nipple, outlet fitting, plug, or block port.
A manifold branch is being added, removed, or reconfigured.
The manifold block or threaded connection is damaged during service.

Troubleshooting

Common PowrCoat 730 Gun Manifold Symptoms

Relieve pressure from every connected gun and hose before inspection. Diagnose pump output, filter condition, coating viscosity, hose restriction, gun filter, spray tip, and branch-valve position before replacing manifold components.

Operating symptom	Inspection points	Recommended action
One gun branch has no coating flow	940-553 or 941-555 valve position, outlet fitting, branch hose, gun filter, tip, nipple, and manifold port	Clear the hose, gun, and tip and confirm valve movement before replacing Titan 940-553 Ball Valve or Titan 941-555 Ball Valve.
A branch leaks while shut off	correct ball valve, internal contamination, valve sealing surfaces, inlet nipple, outlet fitting, and downstream pressure	Flush and cycle the valve after pressure relief before replacing the documented valve for that thread-size family.
Fluid leaks at an inlet nipple	814-002 or 814-004 nipple, thread-size match, manifold port, valve port, thread condition, sealant, and overtightening damage	Identify the configuration and inspect both female ports before replacing Titan 814-002 Hex Nipple or Titan 814-004 Hex Nipple.
Fluid leaks at the gun-hose outlet	227-006 or 808-555 fitting, hose coupling, thread family, damaged threads, sealing method, and branch alignment	Inspect the hose coupling and mating valve port before replacing the matching outlet fitting.
Unused port seeps under pressure	227-033 plug, manifold-block threads, port cleanliness, sealing method, cracks, and incorrect plug installation	Clean and inspect the block port before replacing Titan 227-033 Pipe Plug.
Several gun branches have uneven flow	970-100 block passages, upstream filter, pump capacity, total gun demand, coating viscosity, valve positions, hoses, guns, and tips	Confirm system capacity and clear every branch before replacing Titan 970-100 Manifold Block.

Major Replacement Components

High-Value PowrCoat 730 Gun Manifold Parts

These verified product pages cover every unique component listed on the supplied gun-manifold category, including the alternate 1/4-inch and 3/8-inch parts.

1/4-Inch Manifold Connection

Titan 814-002 Hex Nipple

The documented reducing hex nipple used in the 1/4-inch single-gun and add-a-gun manifold configurations to connect the manifold block and ball-valve path.

View Titan 814-002

3/8-Inch Manifold Connection

Titan 814-004 Hex Nipple

The documented 3/8-inch male-to-male hex nipple used at two positions in the 3/8-inch gun-manifold configuration.

View Titan 814-004

1/4-Inch Flow Control

Titan 940-553 Ball Valve

The documented ball-valve component used in the 1/4-inch gun-manifold configuration to isolate or enable an individual spray-gun outlet.

View Titan 940-553

3/8-Inch Flow Control

Titan 941-555 Ball Valve

The documented ball valve used in the 3/8-inch gun-manifold configuration for controlled on-off flow to a connected gun line.

View Titan 941-555

1/4-Inch Outlet Connection

Titan 227-006 Outlet Fitting

The official 1/4-inch configuration outlet nipple that connects the ball-valve path to the downstream high-pressure gun hose.

View Titan 227-006

3/8-Inch Outlet Connection

Titan 808-555 Fitting

The documented 3/8-inch configuration nipple used between the ball valve and downstream hose connection.

View Titan 808-555

Unused-Port Closure

Titan 227-033 Pipe Plug

Closes an unused manifold-block port so the selected gun-manifold configuration can retain pressure without an open outlet.

View Titan 227-033

Fluid Distribution Block

Titan 970-100 Manifold Block, 3/8

The shared 3/8-inch manifold block used to distribute pressurized coating across the selected single-gun, add-a-gun, or multiple-gun arrangement.

View Titan 970-100

Buying Guide

How to Select the Correct Gun Manifold Component

STEP 1

Identify the assembly family

Confirm single-gun, add-a-gun, or complete multi-gun configuration.

STEP 2

Confirm thread size

Separate the 1/4-inch and 3/8-inch nipple, valve, and outlet columns.

STEP 3

Match the exact callout

Confirm positions 1 through 6 and the exact Titan part number.

STEP 4

Inspect the complete branch

Check block, nipple, valve, fitting, hose, gun, filter, and tip together.

Maintenance

Maintenance Practices That Protect the Gun Manifold

Flush every active manifold branch and connected gun after use.
Cycle each ball valve only after system pressure is relieved.
Inspect nipples, outlet fittings, plugs, and manifold ports for leakage.
Keep valve and block passages free of hardened coating.
Use the correct wrench flats and avoid twisting the manifold assembly.
Confirm every unused port remains closed with the specified plug.

Repair Planning

Build a Complete PowrCoat 730 Gun Manifold Repair

For a 1/4-inch branch, inspect the 814-002 nipple, 940-553 ball valve, 227-006 outlet fitting, connected hose, gun filter, gun, and spray tip. Confirm every component belongs to the same thread-size configuration.

For a 3/8-inch branch, inspect both 814-004 nipple positions, the 941-555 ball valve, 808-555 outlet fitting, 970-100 manifold block, 227-033 pipe plug, and all connected downstream components. Replacing a manifold part will not correct insufficient pump delivery or an obstruction elsewhere.

Fast Navigation

Shop Major PowrCoat 730 Gun Manifold Components

Titan 814-002 Hex Nipple Titan 814-004 Hex Nipple Titan 940-553 Ball Valve Titan 941-555 Ball Valve Titan 227-006 Outlet Fitting Titan 808-555 Fitting Titan 227-033 Pipe Plug Titan 970-100 Manifold Block, 3/8

FAQ Section

PowrCoat 730 Gun Manifold Assembly FAQs

Verified answers for manifold configuration, thread-size selection, branch diagnosis, multi-gun expansion, parts identification, and safe service.

What type of page is the PowrCoat 730 gun-manifold page?+

It is an exploded optional gun-manifold assemblies parts category covering single-gun and multiple-gun fluid-distribution configurations.

Which manifold configurations are documented?+

Titan documents 1/4-inch and 3/8-inch single-gun assemblies, add-a-gun kits, and two-, three-, and four-gun manifold assemblies.

What are the single-gun manifold assembly numbers?+

Titan lists 975-111 for the 1/4-inch single-gun assembly and 975-311 for the 3/8-inch single-gun assembly.

What are the add-a-gun kit numbers?+

Titan lists 975-200 for the 1/4-inch add-a-gun kit and 975-300 for the 3/8-inch add-a-gun kit.

Which complete multiple-gun manifolds are listed?+

Titan lists 975-212, 975-213, and 975-214 for 1/4-inch two-, three-, and four-gun assemblies, and 975-312, 975-313, and 975-314 for the corresponding 3/8-inch versions.

Which nipple is used in the 1/4-inch configuration?+

Titan lists 814-002 at the inlet connection for the 1/4-inch single-gun and add-a-gun configurations.

Which nipple is used in the 3/8-inch configuration?+

Titan lists 814-004 at the inlet and outlet connection positions for the 3/8-inch configuration.

Which ball valves are documented?+

Titan lists 940-553 for the 1/4-inch configuration and 941-555 for the 3/8-inch configuration.

What does the manifold block do?+

Titan 970-100 distributes pressurized coating to the connected valve and gun-outlet paths while unused ports are closed with the specified pipe plug.

Why can one connected spray gun lose flow?+

Possible causes include a closed or restricted ball valve, damaged nipple or outlet fitting, blocked hose or gun, coating contamination, or an obstructed manifold port. Diagnose the entire branch before replacing parts.

Can 1/4-inch and 3/8-inch parts be mixed?+

Do not assume interchangeability. Match the complete assembly family, callout column, thread size, nipple, valve, and outlet fitting shown for the selected configuration.

What safety steps are required before manifold service?+

Lock every spray gun, shut off and vent the air supply, open the bleed valve, trigger each grounded gun into a metal waste container, and verify zero pressure before loosening any manifold connection.

Find the Correct Replacement Part

Restore Reliable Multi-Gun Distribution and Branch Shutoff

Browse diagram-matched manifold blocks, 1/4-inch and 3/8-inch nipples, ball valves, outlet fittings, and unused-port plugs.

Search using:

Titan part number
Manifold diagram callout
1/4-inch or 3/8-inch configuration
Single-gun or add-a-gun assembly
Leakage, shutoff, or flow symptom

PowrCoat 730 Gun Manifold Assemblies Parts

Find Diagram-Matched PowrCoat 730 Gun Manifold Assembly Parts