Titan Air-Powered Airless Sprayer Parts · PowrCoat 730
Find Diagram-Matched PowrCoat 730 Main Assembly Parts
Shop verified replacement components for the PowrCoat 730 Main Assembly, including the cart assembly, plug, 16-inch wheel, retaining ring, washer, mounting hardware, muffler kit, 45-degree elbow, bypass tube, hose tie clamp, cart-model suction set, wall-model suction set, and inlet screen. Confirm the machine configuration, exploded callout, and exact Titan part number before ordering.
How the PowrCoat 730 Main Assembly Supports the Sprayer
This is an exploded replacement-parts category covering the PowrCoat 730 machine’s primary support, mobility, pneumatic exhaust, material-intake, bypass, and hose-management components. Titan identifies cart model 0533730C and wall model 0533730W. The verified technical data specifies a 30:1 pressure ratio, 3,000 PSI maximum operating pressure, and 100 PSI maximum air inlet pressure.
The page lists Titan 0533203A Cart Assembly, 9885571 Plug, 670-105 Wheel, 590-100 Retaining Ring, 870-003 Washer, 9805429 Screw, 0509285 Flat Washer, 862-410 Locknut, 830-340 Muffler Kit, 830-345 Elbow, 0533325 Bypass Tube, 730-334 Hose Tie Clamp, 0533237A cart-model suction set, 0533238A wall-model suction set, and 0509762A Inlet Screen.
Functions Supported by the Main Assembly
- Supports mobile operation with the cart, wheel, retaining, washer, and fastening components.
- Reduces and directs pneumatic exhaust through the muffler and elbow.
- Draws coating through the correct cart- or wall-model suction assembly.
- Reduces debris entry with the listed inlet screen.
- Routes bypass material and secures hoses to the machine structure.
When Contractors Use This Parts Diagram
- Cart instability, wheel wear, missing retaining hardware, or loose frame hardware.
- Increased pneumatic exhaust noise or damaged muffler components.
- Poor priming, weak material pickup, or a clogged inlet screen.
- Cracked, loose, or incorrect cart- or wall-model suction assembly.
- Damaged bypass tubing or unsecured hose routing.
Common PowrCoat 730 Main Assembly Symptoms
Perform the pressure-relief procedure and vent the air supply before inspection. Diagnose connected pump, hose, air-motor, and coating-supply conditions before replacing a visible component.
High-Value PowrCoat 730 Main Assembly Parts
These verified products cover the principal cart, wheel, exhaust, suction, and intake-filtration positions shown on the supplied page.
Titan 0533203A Cart Assembly
Complete mobile support assembly for PowrCoat 730 cart configurations, restoring stable equipment positioning and transport.
Titan 670-105 Wheel
OEM 16-inch wheel used on the PowrCoat 730 heavy-duty cart to restore mobility and stable jobsite handling.
Titan 830-340 Muffler Kit
Reduces air-motor exhaust noise and supports controlled discharge from the pneumatic motor system.
Titan 0533237A Suction Set Assembly with Filter Screen
Complete 5-gallon material suction assembly with filter screen for the PowrCoat 730 cart model.
Titan 0533238A Suction Set Assembly
55-gallon drum-fed suction assembly for the PowrCoat 730 wall-mount configuration.
Titan 0509762A Inlet Screen
Screens coating at the suction inlet to reduce debris entry and support cleaner priming and material flow.
How to Order the Correct Main Assembly Part
Identify the system area
Determine whether the issue involves cart structure, exhaust, suction, bypass routing, or intake filtration.
Confirm configuration
Verify cart model 0533730C or wall model 0533730W.
Match the callout
Use the exploded drawing to match the item number and exact Titan part number.
Inspect connected parts
Check retainers, washers, fasteners, fittings, clamps, hoses, screen, and mating components.
Maintenance Practices That Protect the Main Assembly
- Inspect cart hardware, wheel retention, and tire condition before transport.
- Keep the muffler and exhaust elbow free of debris and impact damage.
- Clean the inlet screen and strain coating before spraying.
- Inspect suction hoses and fittings for cracks, flattening, looseness, and air leaks.
- Secure bypass and suction lines so they cannot rub, kink, or contact moving parts.
- Verify fluid and air connections before pressurizing the system.
Build a More Complete PowrCoat 730 Main Assembly Repair
Cart repairs should include the cart assembly, wheel, retaining ring, washer, screw, flat washer, locknut, and attachment points. A new wheel will not correct a missing retainer, bent support, loose hardware, or damaged washer stack.
Material-intake repairs should include the correct suction set, inlet screen, bypass tube, hose tie clamp, intake fittings, hose condition, and pump inlet. Exhaust repairs should include the muffler, elbow, air-motor discharge, and mounting security.
Shop Major PowrCoat 730 Main Components
PowrCoat 730 Main Assembly FAQs
Contractor-focused answers for identification, diagnosis, configuration, and replacement planning.