Most Impact X wear comes down to dirty paint, dry packings, paint left to cure in the system and tips used past their life. Clean the inlet screen and 60 mesh filter after every job, keep the packings lubricated with Piston Lube, flush with the right fluid, and replace the tip when the pattern coarsens. Titan publishes no service interval for any wear part, so judge by symptoms.
Titan does not publish hours or gallons of life for the packings, seats, balls or filter on any Impact model, so this guide gives no such numbers. What follows are habits that protect those parts, each tied to something Titan says or to a part on the site's Impact X diagram pages.
Keep paint clean on the way in
Grit and skins in the paint score the piston rod and chew up seats and balls, so the first defence is filtering. Airless sprayers usually have a suction (inlet) strainer, a pump filter and a gun filter. Clean all three after every job, and strain and stir the coating before you pump it. Titan's Impact 640 manual says to inspect the pump filter and gun filter and clean or replace them.
On an Impact X the pump filter is the 60 mesh 2424933 in a vertical housing, and Titan says that design cleans up to three times faster with as little as one third the water. The inlet screen filter on the Suction Set page is 700-805. The accessories pages list inlet screens in 10 mesh (710-046B) and 30 mesh (710-191A), and gun filters in coarse (0089957) and 100 mesh (0089959). Pick a mesh suited to the coating.
Lubricate the packings
The piston rod moves through packings that seal it, and Piston Lube keeps them lubricated. The site lists 314-480 (8 oz) and 314-481 (4 oz), and the Impact X 410 ships with the 4 oz bottle. Titan's Impact manuals cover how much to use and when for each model, and the Impact X manuals are on our manuals page.
We do not state a lubrication interval. A scored or dirty piston rod destroys new packings, so if you replace packings and the leak returns quickly, inspect the rod first.
Flush after every job and store correctly
- Flush the gun outdoors, at least one hose length from the pump, with the gun grounded against the edge of a metal container (Titan's Impact 640 manual).
- For short-term storage with latex, pump water mixed with Titan Liquid Shield (314-482) through the whole system.
- For long-term or cold-weather storage, the same manual says to pump mineral spirits through the whole system.
- Never leave latex or any coating to dry in the pump, hose or gun.
That storage guidance comes from the Impact 640 manual, with an Impact 340 excerpt that agrees. Check your own Impact X manual for any differences.
Replace the tip before the pump pays for it
A worn tip has a wider orifice. Pressure falls, the pattern gets coarse or streaky and more paint is used, and the pump works harder to make up the difference. Replace the tip when the pattern degrades rather than turning the pressure up. The 661-020 tip seat and seal kit and the tip guard (0289228A) are listed on the accessories pages.
Treat hose, gun and fluid section as a system
Never run any component above the lowest working-pressure rating in the system. The site's 50 ft hose (316-505) and whip hose (316-506, listed as 3300 PSI) are the ones on the Impact X pages. Titan's Impact manuals say surge or pulsing at the gun points to worn upper packings. The repacking kit on the Impact X 440 and X 540I fluid section pages is 704-586B.
A short end-of-day routine
Relieve pressure
Use the procedure in your manual.
Clean the filters
Pump filter, gun filter and inlet screen.
Flush
Outdoors, gun grounded, with the right fluid for the coating.
Lubricate and store
Packing lube as the manual describes, then storage fluid if the manual calls for it.
The accessory and filter parts are on the Impact X 440 Accessories, Impact X 540I Accessories, Filter Assembly and Suction Set pages.
Wear and care parts for Impact X sprayers:
The Short Version
Filter every job, keep the packings lubricated, flush with the right fluid, and replace a worn tip early. Titan publishes no life figures for wear parts, so judge by symptoms and your manual, and call (713) 931-0006 if you are unsure which part is next.
Which wear part is next?
Call (713) 931-0006 with your Impact X model and what the sprayer is doing, and our parts team will point you to the right diagram.
(713) 931-0006Order by Parts Diagram