The PowrLiner 850 accessories page lists TR1 line striping tips, Piston Lube, Liquid Shield and a suction set, and the 850 gun, hose and stencil parts are on its other diagram pages. Start with spare tips, tip seals and a gun filter, since those wear first. Confirm fitment for stencil kits by phone before ordering.
A PowrLiner 850 leaves the factory ready to stripe: Titan lists one gun, a 419 line striping tip and a 1/4 inch by 50 ft hose with it. What you add depends on whether you want to stripe more kinds of line, stencil, carry spares so a worn part does not stop a job, or protect the pump. This guide goes through the accessories our site lists for the 850 and says what each is for.
TR1 line striping tips
Tips are the accessory you will buy most often. Titan supplies its own TR1 reversible line striping tips, and the 419 is the one that comes with the 850. Our 850 accessories page lists many more, including 697-415, 697-619, 697-421, 697-821 and 697-213. The first digits of a TR1 number tell you something about the tip, but Titan's material we have does not spell out the code, so we will not guess. Check the tip chart in your manual or call us with the line width and paint you plan to use.
The general rule applies to every tip: the orifice controls how much paint is delivered and the fan angle sets the width of the pattern. A worn tip has a wider orifice, pressure drops, and lines turn coarse. Keep a spare of the tip you run most so a bad line does not end the day. Reversible tips can clear a clog by rotating the handle as the tip's instructions describe.
Gun-side parts to keep on the truck
The 850 spray gun page shows the small parts that wear. Tip seals come as 651-020 and 0297007. The 581-060 white filter is the gun filter, which Titan's manual says to clean after every use. The 661-010A black guard assembly is the guard on the gun, and the 759-369 gun assembly is the whole gun if you want a spare or a second one ready.
Hose
The 850's hose connection is 1/4 inch NPS(M) and Titan supplies a 1/4 inch by 50 ft hose. The 316-505 50 ft spray hose is on the 850 main assembly page. Whatever hose you add, it must be airless rated and its working pressure must not be lower than the pump's 3000 psi maximum, and the same goes for fittings. Do not mix in an unrated hose.
Lubricant and pump protection
The 850 accessories page lists Piston Lube in two sizes, 314-480 (8 oz) and 314-481 (4 oz bottle), and Liquid Shield in 314-482 (1 quart) and 314-483 (Plus, 4 oz bottle). Titan says Piston Lube prevents increased wear on the packings in its hydraulic models, and the 850's packings are lubricated through the AutoOiler, which the manual has you press 2 to 3 times before each use. Read the label and your manual for how each product is meant to be used on your machine.
The 0293932 suction set is also listed as an accessory. If you pull paint from a pail, a spare saves a lost job if a hose cracks or the strainer is damaged.
Stencil kits and the removable gun
Titan describes the 850 gun as removable for stenciling, and the gun mount reverses so you can stripe from the front or rear tire. Our 850 accessories page lists the 0290933 starter stencil kit and the 0290934 professional stencil kit. Their fitment text on the product pages names other PowrLiner models, such as the 550 and 2850, and does not list the 850 by name, so confirm with us on (713) 931-0006 before you order.
How to decide what to add
Accessory by need
| If you want to | Look at | Page |
|---|---|---|
| Keep working when a tip wears | Spare TR1 tip | 850 accessories |
| Stop leaks around the tip | Tip seal 651-020 or 0297007 | 850 spray gun |
| Protect against pressure loss from a blocked gun filter | Gun filter 581-060 | 850 spray gun |
| Extend or replace hose | 316-505 50 ft hose | 850 main assembly |
| Look after the packings | Piston Lube 314-480 / 314-481 | 850 accessories |
| Stencil arrows and symbols | Stencil kits, after fitment check | 850 accessories |
Popular 850 accessories, with live pricing and Add to Cart:
TR1 tips, Piston Lube, Liquid Shield, stencil kits and suction set.
Gun assembly, tip seals, filter and guard.
Hose, suction set, wheels and filter cover.
Bottom line
Order spare tips, a tip seal and a gun filter first, then lubricant, then a stencil kit if you need arrows and symbols. For fitment questions on kits, call (713) 931-0006 with your model and serial number.
Not sure an accessory fits your 850?
Call with your model and serial number, or order from the 850 diagram pages.
(713) 931-0006Order by Parts Diagram