Please wait while we process your order...

Link copied!
Genuine OEM Parts For
Impact 640 Main Assembly Impact 640 Fluid Section Genuine OEM Filters Fitment Help: (713) 931-0006
In Short

Most Impact 640 trouble traces back to a few things: coating left to dry in the system, dirty filters, a worn tip, and worn packings or valves. The routine below covers cleaning after every job, filter checks, packing wear signs and a periodic fluid section inspection on the Titan Impact 640. AllTitanParts.com sells the parts it calls for, and most available items are processed for shipment within about 1-2 business days.

Why Routine Care Beats Reactive Repairs

A Titan Impact 640 that gets regular attention reaches a major repair less often than one that gets attention only when something fails. Small wear items like filters and packings degrade gradually, and a sprayer run on a partly worn component works harder to deliver the same result. Titan's manual lists dirty filters among the causes of a poor spray pattern and a clogged tip, and worn packings among the causes of pulsing and lost pressure.

Titan does not publish fixed service intervals for packings, valves or filters that we can quote, and usage varies a lot between contractors. This page is organized by task and symptom, not by calendar. Your owner's manual, on our manuals page, is the authority for the exact steps.

After Every Job

  • Relieve pressure first, following the pressure relief procedure in your manual, before cleaning or servicing anything.
  • Flush the sprayer thoroughly with the fluid your manual and the coating call for. Never leave latex or other coatings to dry in the pump, hose or gun.
  • Flush the gun outdoors, away from the pump, with the gun grounded against the edge of a metal container, as the 640 manual describes.
  • Wipe down the exterior and look for fresh leaks around fittings or the gun connection.
  • Inspect the suction set and inlet screen for debris picked up during the job.

Filters and Lubrication

An airless system usually has an inlet screen, a pump (manifold) filter and a gun filter. Titan's manual says to inspect the pump filter and the gun filter and clean or replace them, since a partly blocked filter causes pressure loss, pulsing and spitting. On the 640 diagrams the 60 mesh manifold filter is 730-067 and the inlet screen filter is 700-805. The gun filters are 0089957 (coarse) and 0089959 (100 mesh).

The 640 has an AutoOiler: Titan describes it as a button that delivers oil from the reservoir to the packings. Piston lube on the site is 314-480 (8 oz) and 700-926. Use the lube and the method in your manual.

Titan 730-067 60 Mesh Manifold Filter #1 Seller
Titan
Titan 730-067 60 Mesh Manifold Filter
Part #: 730-067
(1)
$18.00
Buy Now
Titan 700-805 Inlet Screen Filter −8%
Titan
Titan 700-805 Inlet Screen Filter
Part #: 700-805
$24.56 $26.74 Save $2.18
Buy Now
Titan 0089959 Filter, 100 Mesh, Yellow #1 Seller
Titan
Titan 0089959 Filter, 100 Mesh, Yellow
Part #: 0089959
$16.30
Buy Now
Titan 314-480 Piston Lube 8oz #1 Seller
Titan
Titan 314-480 Piston Lube 8oz
Part #: 314-480
$15.10
Buy Now
Titan 704-564 Upper Packing Kit −8%
Titan
Titan 704-564 Upper Packing Kit
Part #: 704-564
$40.47 $43.80 Save $3.33
Buy Now

Packing and Pressure Signs

Pay attention to how the sprayer behaves at the gun compared with when it was new. Titan's manual points to worn upper packings when there is excessive surge or pulsing at the gun, and to worn packings, worn valve balls or worn seats when fluid leaks at the top of the fluid section or pressure will not build or hold. Catching it early usually means a straightforward repacking job rather than a bigger repair. For the step-by-step diagnosis, see Impact 640 Won't Prime or Build Pressure.

Check the simple things first The manual lists an air leak at the suction set, a clogged filter or inlet screen, and a worn tip ahead of a worn fluid section. A new tip or a clean filter costs less than a fluid section repair, so rule those out before you open the pump.

Periodic Fluid Section Inspection

From time to time, or when symptoms point there, it is worth a closer look at the fluid section than a quick visual check gives you. Titan's manual describes reaching the inlet valve, reversing or replacing the seats, and repacking by removing the upper and lower packings and cleaning the pump block. Follow it for the steps, and follow the pressure relief procedure before you start.

  • Inspect the piston rod: it should be smooth, since a scored rod damages new packings.
  • Check the inlet and outlet valve seats and balls for wear.
  • Look at the main assembly: power switch, ground screw and motor screws on the main assembly page.
  • Check the drive side on the drive assembly page if the machine will not run or sounds wrong, and see your manual for the troubleshooting order.

Keeping a Maintenance Log

A simple log noting the date of each filter change, each repacking and any larger repair turns this routine into an actual record. Over a season it shows how your own job mix wears the machine, which is more useful than generic guidance, and it saves guessing the next time a symptom shows up.

Warning Signs Between Services

A few signs mean you should not wait: pressure that drops suddenly rather than gradually, fluid leaking anywhere on the machine, or the motor getting too hot. Titan's manual says to let a motor that is too hot cool down, and it says the Digi-Trac display can show an error such as High Control Temperature or Check Motor, after which the sprayer shuts down and the manual points you to a Titan service center. Stop spraying, relieve pressure and inspect.

Storage

How you store the 640 matters as much as how you clean it. Titan's manual describes pumping mineral spirits through the whole system for long-term or cold-weather storage, and water mixed with Titan Liquid Shield for short-term latex storage. Liquid Shield on the site is 314-482 (1 quart) and 314-483 (Liquid Shield Plus, 4 oz). Check your manual for the exact method.

Where the Parts Are on the Diagrams

Each assembly has its own page, so a symptom is easy to trace to a part number.

How to Order Maintenance Parts

AllTitanParts.com is an Authorized Titan Dealer supplying genuine OEM replacement parts for Titan, SpeeFlo, SprayTech and Wagner equipment, based in Houston, Texas. Orders are processed on business days with a 12 pm Eastern cut-off. Most available items are processed for shipment within about 1-2 business days, and some items are ordered from the manufacturer after you order, so availability shown does not always mean an item is on a shelf. Plan a little ahead of a big job, and see Shipping Info for the delivery estimates.

Build Your Impact 640 Parts Kit

Tell us your model and what you spray and we'll help you pick the right filters, packings and wear parts.

(713) 931-0006 Shop Impact 640 Parts
Frequently Asked Questions
What routine care does a Titan Impact 640 need?
Relieve pressure as your manual describes, flush the sprayer after every job, clean or replace the pump and gun filters, keep the packings lubricated and store the machine with the fluid your manual recommends. Titan publishes no fixed service intervals that we can quote, so go by symptoms and your manual.
What is the earliest sign of packing wear on an Impact 640?
Titan's manual lists excessive surge or pulsing at the gun as a sign of worn upper packings, and fluid leaking at the top of the fluid section or pressure that will not build or hold can also point to worn packings or valve balls. Check your manual for the full troubleshooting steps.
Do I need to flush the machine after every job?
Yes. Never leave latex or other coatings to dry in the pump, hose or gun. Flush after every use and follow your manual for the right fluid and for flushing the gun outdoors.
What should I check first if the Impact 640 will not hold pressure?
The manual lists an air leak at the suction set, a clogged filter or inlet screen, a worn tip, and a worn fluid section. Check the filters, suction set and tip first, then service the packings and valves if the manual points there.
Is it worth keeping a maintenance log?
Yes. A simple log of filter changes and repacking dates shows how your own jobs wear the machine, which is more useful than generic guidance.
How fast do Impact 640 maintenance parts ship?
Orders are processed on business days with a 12 pm Eastern cut-off. Most available items are processed for shipment within about 1-2 business days, and standard delivery is generally expected about 4-5 business days after shipment. These are estimates, some items are ordered from the manufacturer after you order, and smaller orders may take 5-7 business days to ship. See the Shipping Info page for details.
On this page

Added to cart

Your Cart
No items in cart.
Add more items
Total 0
Checkout Modify Cart