The Titan Impact 840 sits between the 740 and the 1040 in Titan's electric Impact line: Titan lists 1.00 gpm and a 0.032 inch maximum tip for the 840, against 0.80 gpm and 0.029 inch for the 740 and 1.15 gpm and 0.033 inch for the 1040. Pick by tip size, number of guns and the coatings you spray. AllTitanParts.com, based in Houston, Texas, supplies genuine OEM parts for the whole range. Most available items are processed for shipment within about 1-2 business days.
Where the 840 Sits in the Lineup
All of these are electric piston-pump airless sprayers with a listed maximum pressure of 3300 psi, so the real differences are flow, tip size and features. Titan describes the Impact 840 for stains, lacquers, enamels, latex and block fillers on medium to large residential, commercial and industrial work. Here are the numbers Titan lists:
| Model | Max delivery | Max tip, 1 gun | Max tip, 2 guns | Motor |
|---|---|---|---|---|
| Impact 740 | 0.80 gpm | 0.029" | not listed here | 2.0 hp brushless DC |
| Impact 840 | 1.00 gpm | 0.032" | 0.021" | 2.3 hp brushless |
| Impact 840I / 840IA | 1.00 gpm | 0.032" | 0.021" | DuraLife HE brushless |
| Impact 1040 | 1.15 gpm | 0.033" | 0.022" | 2.5 hp brushless |
The 840I and 840IA have the same delivery, tip and pressure numbers as the 840. A different number on the sprayer's label or in your manual always wins over a general comparison, so confirm your exact model before you order parts.
840 vs 740
On Titan's numbers the step from 740 to 840 is 0.20 gpm more delivery and a 0.003 inch larger maximum tip. Titan lists a weekly volume of 150-200 gallons for the 740 and 200-300 gallons for the 840, which is a useful way to judge how hard you will work the machine. The two also overlap on the parts side: this site groups them on shared diagram pages, including the 740/840 fluid section assembly, the 740/840 drive assembly and the 740/840 upright cart. If your work is mostly standard coatings through mid-size tips, the smaller machine may be all you need. If you regularly run tips near the 740's limit, the 840 gives you more room.
840 vs 1040: Tip Size and Two Guns
The 1040 is listed at 1.15 gpm and a 0.033 inch maximum tip, against 1.00 gpm and 0.032 inch for the 840. For two-gun work Titan's maximum tip is 0.022 inch on the 1040 and 0.021 inch on the 840, so the gap is small on paper. Titan describes the 1040 for demanding, high-volume coating work. If you run a single gun on typical commercial coatings, compare your actual tip size against the 840 numbers first. If your tips or your two-gun setup sit at the upper end of what the 840 is listed for, the 1040 is the next step up. Its parts pages are separate from the 840's: see the 1040 fluid section and 1040 main assembly diagrams.
840 vs 840I/IA IntelliSync
The 840I and 840IA are part of Titan's Impact IntelliSync series. Titan lists the same delivery, tip and pressure numbers as the standard 840, and adds a Bluetooth link to the MyTitan app, which Titan says shows supply levels, pressure, runtime and paint usage and sends maintenance alerts. Titan lists DigiTrac diagnostics on the 840I and ActivGuard GPS tracking, which needs a subscription, on the 840IA. Titan also lists its Logix Adaptive Pressure Control on these models, which adjusts pump speed to the tip size.
The original 840 is not a bare machine either: its main assembly diagram shows a Digi-Trac display (805-401). So the decision is mostly about the app, the tracking and the controls, not about spray capacity. Our post on 840I vs 840IA covers the part numbers in more detail.
What These Models Share
Staying inside the Impact family helps when one crew runs more than one machine. These come straight from the site's diagrams. Where two models list the same part number, that is a diagram fact, not a promise that every assembly swaps over.
- The 740, 840 and 1040 fluid-section diagrams list the same outlet ball (9841502), outlet seat (0294516), inlet seat (00310), outlet seal (800-348) and Viton O-ring (800-332).
- The 740, 840 and 1040 also list the same inlet ball (51519).
- The 740/840 and 1040 drive diagrams list the same slider assembly (805-241A).
- The motor, controller, cart and packing kits are different between the 840 and the 1040, so order those from the page for your own model.
Making the Decision
Start from your tip size and number of guns, then your coatings, rather than the biggest number on a sheet. If your tips fit comfortably within the 840's 0.032 inch single-gun maximum, the 840 covers a wide range. If you routinely work at the top of that range or want more delivery, look at the 1040. If the app, usage data or GPS tracking matters to you, look at the 840I or 840IA. Whichever you pick, the parts diagrams make it easy to see what each machine's service parts look like before you commit.
Buying Used Within This Range
The same comparison applies to a used machine, with one addition: check the condition of the fluid section. Ask for service records if there are any, and ask which packings, seats and balls have been replaced. Because those wear parts are listed on the diagram, you can see exactly what a rebuild would involve. The 740/840 fluid section page lists every piece.
What to Check Before You Order
Look at the label on your sprayer for the exact model, since the 840, 840I and 840IA have their own listings. Then open the matching diagram: the 840 main assembly, the 840 filter assembly and the 840 fluid section are good starting points. Manuals for your model are on the manuals page. For help sizing a machine to your work, see Is an Impact 840 the Right Size?
How to Order Parts for Any Model in the Range
AllTitanParts.com is an Authorized Titan Dealer supplying genuine OEM replacement parts for Titan, SpeeFlo, SprayTech and Wagner equipment, based in Houston, Texas. The order cut-off is 12 pm Eastern on business days. Most available items are processed for shipment within about 1-2 business days, and some items are ordered from the manufacturer after you order, so availability shown does not always mean an item is on a shelf (see Shipping Info for delivery estimates). Call (713) 931-0006 with your exact model if you are unsure which parts apply to the 740, 840, 840I/IA or 1040.
Not Sure Which Impact Model Fits Your Job?
Tell us your typical tip size and coatings and we'll help you match the parts and the model.
(713) 931-0006 Shop Impact 840 Parts