Titan's text for the PowrBeast 7700 lists stains, lacquers, epoxies, enamels, elastomeric, latex, dry fall and block fillers, and recommends it for large projects or heavy coatings. A listing is not a promise for every product in a category, so check your coating's data sheet for tip size, thinning and clean-up before you spray it.
When a painter asks whether the PowrBeast 7700 will spray a given coating, the useful answer has two parts: what the manufacturer says the sprayer is for, and what your coating's maker says it needs. This guide covers the first part from Titan's own wording and then lists what to read off the can for the second. We are not promising that any particular product will spray well, and we have not listed tip sizes for any coating, because the data sheet decides that.
What Titan lists
Titan's page for the PowrBeast 7700, 230V model says it sprays stains, lacquers, epoxies, enamels, elastomeric, latex, dry fall and block fillers, and that it is recommended for large projects or heavy coatings. The same wording is used on listings of the gas 7700. Titan's series description for the whole PowrBeast line also calls the units hydraulic-drive, direct immersion airless sprayers built for heavy and light bodied coatings.
Coatings in Titan's list for the 7700
| Coating | Where to look before you spray it |
|---|---|
| Latex | Strain it, then flush promptly. Latex left to dry in the pump, hose or gun is a clean-up problem. |
| Elastomeric | A thick coating. The data sheet's tip recommendation matters, and so does the sprayer's tip limit for your gun count. |
| Epoxies | Follow the maker's mixing, thinning and clean-up instructions to the letter; they differ by product. |
| Enamels | Check the data sheet for tip size and any thinning the maker allows. |
| Lacquers | Solvent-based. Read the coating's safety data and your manual's warnings, and keep gas-engine fuelling and running outdoors or in ventilated areas away from ignition sources. |
| Stains | Thinner materials can be sprayed through smaller tips; check the data sheet. |
| Dry fall | A specialty coating with its own application notes from the maker. |
| Block fillers | A heavy, graded material. This is the case Titan's foot valve wording is aimed at. |
The right column is general airless practice, not a Titan instruction for each coating. The coating maker's data sheet and your manual come first.
Why a hydraulic-drive unit suits thick materials
Titan describes the PowrBeast series as using HydraStroke Technology, which it calls digitally driven hydraulics. Two lines from Titan's text bear on coatings. The first says the sprayer can handle heavy and light bodied coatings without worry of burning out clutches: there is no clutch in the drive to burn. The second says the series has one moving part in that system, which reduces heat and extends life.
Retailer copy of Titan's text for the 7700 also describes a submersed foot valve that maximizes suction for heavy graded materials. A thicker coating is harder to draw into the pump, so a design that favours suction is relevant to block fillers and heavy elastomerics. This is the manufacturer's description of the feature, and it is not a measured result from us. Titan also describes a fan and shroud, plus a radiator-style cooling hydraulic tank, for keeping temperatures down.
Tip size and coating
The tip does two jobs. The orifice size controls how much material is delivered, and the fan angle controls how wide the pattern is. Thicker coatings generally need a larger orifice, and finer finishes use a smaller one. The coating maker's data sheet tells you which orifice and fan angle to start from, and the sprayer then sets a ceiling: the largest tip you can run depends on how many guns are on the sprayer and on whether it is the gas or the 230V model. Titan publishes that ceiling, and it is not repeated here.
A worn tip has a wider orifice. Pressure falls, the pattern gets coarse or streaky, and more paint goes on the wall. With abrasive or heavy coatings it is worth looking at the pattern on a test board before you commit to the whole wall. The 661-020 tip seat and seal kit and the 0289228 tip guard are listed on the 7700 accessories page or the 9700 equivalents; if the one you need is not on the page, call us.
Prep
- Strain and stir. Lumps and skins block tips and filters, and settled solids change how the coating sprays.
- Thin only as the coating maker allows. If the data sheet says do not thin, do not thin. If it gives a limit, stay inside it.
- Match the fluid to the sprayer. Different coating families can call for a different class of sprayer. Titan recommends the 7700 for large projects or heavy coatings; a small touch-up job is a different case.
- Read the manual's priming and start-up steps on the manuals page. We do not give model-specific steps here.
Filters and clean-up
Airless systems usually have a suction strainer, a pump or manifold filter, and a gun filter. A partly blocked filter causes pressure loss, pulsing and spitting, and the filter mesh should suit the coating. On the 7700 the high pressure filter is the 0537220A, and its diagram page lists the 0537454A filter body, three manifold filters (930-005, 930-006 and 930-007), and the 930-050 filter service kit. The product pages state what each manifold filter is, so choose the one that matches your coating rather than the one you happen to have. The 0089959 is a 100 mesh gun filter.
Flush and clean the sprayer after every use. Latex and other coatings left to dry in the pump, hose or gun are the most common reason a good sprayer behaves badly the next morning. Store it with the fluid the manual recommends, and protect the pump against freezing as the manual describes. The wet cup lube 314-480 and Liquid Shield 314-482 are on the 7700 accessories page as well.
Parts to pair with heavier coatings
Heavy coatings work the whole fluid path harder. Keep spare tips and seats, a filter service kit and a gun that suits you. The 0538020 RX-Pro gun with 517 TR1 tip is the gun listed on the accessories page and included with the unit. If the pump itself is slow to prime or leaks at the wet cup, look at the packings and valves on the fluid section page for the 0537256 pump end; the diagram index starts at PowrBeast Gas & Electric Sprayer Parts.
Parts that pair with a 7700 coatings setup:
−15%
The Short Version
Titan lists stains, lacquers, epoxies, enamels, elastomeric, latex, dry fall and block fillers for the 7700. That tells you the sprayer is built for the job, and your coating's data sheet tells you the tip, the thinning and the clean-up. Strain, flush after every use and keep the tip and filter parts on hand.
Not sure your coating suits the 7700?
Call (713) 931-0006 with your model and serial number and our parts team will help you choose tips, filters and seals.
(713) 931-0006Order by Parts Diagram