Titan 353-708 controlMax Hose
Keep coating material moving from your sprayer pump to the spray gun with the Titan 353-708 ControlMax Hose. This replacement hose is identified for use with compatible Titan ControlMax airless spraying equipment, providing the flexible fluid-delivery connection required between the sprayer outlet and spray gun. It is a practical replacement when the existing hose is damaged, leaking, or otherwise unsuitable for safe operation.
Application: Pressurized coating-material delivery between the sprayer and spray gun.
A targeted replacement for a damaged, leaking, kinked, or excessively worn spray hose. Confirm hose length, pressure rating, and fitting compatibility before ordering.
Extend Your Spraying Reach with the Titan 353-708 ControlMax Hose
Improve maneuverability and maintain dependable coating delivery with the Titan 353-708 ControlMax Hose. This 50-foot High Efficiency Airless spray hose is designed for compatible Titan ControlMax spraying systems, offering a flexible connection between the pump and spray gun. Its durable polyethylene jacket and extended length make it a practical replacement or additional hose for painting projects requiring greater working reach.
How the Titan 353-708 ControlMax Hose Supports Spraying Performance
The spray hose forms the pressurized fluid connection between an airless sprayer pump and its spray gun. During operation, coating material travels through the hose before reaching the spray tip, where it is atomized into the spray pattern.
The Titan 353-708 provides a 50-foot working length that can help operators reach larger surfaces, move around obstacles, and reduce unnecessary sprayer repositioning. Its flexible construction is particularly useful when working across walls, ceilings, and other surfaces within the operating limits of the equipment.
When Should You Replace Your ControlMax Spray Hose?
Inspect the spray hose before each use and consider replacement when any of the following conditions are present:
- Visible cracks, cuts, or excessive abrasion on the hose jacket.
- Coating material leaking from the hose body or permanently attached fittings.
- Severe kinks, crushing, or deformation that could compromise hose integrity.
- Damaged fitting threads or connections that cannot be secured correctly.
- A hose that does not meet the pressure or connection requirements of the intended sprayer.
Never attempt to repair a damaged high-pressure spray hose with tape, clamps, or improvised fittings. Remove defective hoses from service and replace them with an appropriately rated assembly.
Titan 353-708 is intended for compatible HEA spraying systems. Do not assume it is suitable for every Titan airless sprayer, particularly conventional high-pressure models. Confirm the hose pressure rating, fitting compatibility, and permitted total hose length before installation. Manufacturer documentation should take precedence over broad retailer compatibility claims.
Shop Related Titan ControlMax Spray Parts
Maintain your ControlMax spraying system with compatible replacement hoses, spray guns, guards, tips, and other service components.
Installation and Safety Guidance
Before disconnecting or replacing the spray hose, switch off the sprayer, disconnect electrical power, and complete the pressure-relief procedure described in the manufacturer's operating manual. Airless spray equipment can retain hazardous pressure after shutdown.
Check the hose and fittings for damage before installation. Connect the hose using the manufacturer's approved procedures, ensure that all fittings are properly secured, and route the hose away from sharp edges, hot surfaces, vehicle traffic, and locations where it may be crushed.
After installation, inspect for leaks using safe procedures and verify correct sprayer operation. Never touch a suspected high-pressure leak or place any part of the body in front of a spray outlet. High-pressure coating injection injuries require immediate emergency medical attention.
Frequently Asked Questions
Helpful compatibility, installation, and replacement information for Titan 353-708.
What is Titan 353-708 ControlMax Hose?
Titan 353-708 is a 50-foot High Efficiency Airless spray hose used with compatible Titan ControlMax spraying systems. It transfers coating material from the sprayer pump to the spray gun.
How long is the Titan 353-708 hose?
The hose is 50 feet long, approximately 15.24 meters, providing extended working reach for compatible HEA spraying equipment.
Which Titan ControlMax sprayers use hose 353-708?
Titan parts documentation lists 353-708 for ControlMax 1700 Pro and 1900 Pro configurations. It is also marketed as an additional HEA hose for compatible ControlMax 1500 and 1700 systems, subject to manufacturer requirements.
Can I use Titan 353-708 to extend my existing spray hose?
The hose is marketed for additional HEA spraying reach. However, extensions should only be used when permitted by the sprayer manufacturer. Check the maximum allowable total hose length, connection requirements, and pressure rating.
What is the difference between Titan 353-706, 353-707, and 353-708?
Manufacturer parts documentation identifies 353-706 as a 25-foot ControlMax hose, 353-707 as a 30-foot hose, and 353-708 as a 50-foot hose. Select the correct hose for your sprayer and intended configuration.
Can Titan 353-708 be used on conventional high-pressure airless sprayers?
Do not assume compatibility. The hose is designed for HEA applications, and its pressure rating must be suitable for the maximum operating pressure of the sprayer. Check the hose marking and manufacturer documentation before use.
When should I replace my ControlMax spray hose?
Replace the hose if it develops leaks, cracks, severe abrasion, permanent kinks, damaged fittings, or other conditions that compromise safe pressurized operation.
Where can I buy Titan 353-708 ControlMax Hose?
You can view the Titan 353-708 ControlMax Hose at AllTitanParts. Confirm the hose specifications and your sprayer's compatibility before ordering.
No reviews yet. Be the first to review this product!