Titan's LCX 130 spec sheet lists 1.30 gpm and 3300 psi, with a 0.035 inch maximum tip on one gun and 0.025 inch on two. Our site breaks the striper into fifteen diagram pages, from the fluid section and drive to a line laser, second gun kit and 12 gallon hopper. Open the page that matches the symptom.
What the spec sheet says
The LCX 130 figures below come from Titan's spec sheet. It is a single source, so treat them as the manufacturer's listed ratings, and check your own machine's manual for anything that affects safe operation.
LCX 130 listed specifications
| Item | Titan listing |
|---|---|
| Maximum delivery | 1.30 gpm |
| Maximum pressure | 3300 psi |
| Largest tip, one gun | 0.035" |
| Largest tip, two guns | 0.025" |
| Weight | 272 lbs |
Source: Titan LCX 130 specification sheet.
The two tip figures matter when you plan a job: Titan lists a smaller largest tip when two guns run than when one does. The site lists a second gun kit as its own page.
How the striper breaks down on our site
Our catalog carries fifteen LCX 130 pages under the LCX, LC and ProMark Gas Line Striper Parts heading. Grouped by job, they look like this.
- Pump end: Fluid Section Assembly, Prime/Spray Valve Assembly, Filter Assembly, Siphon Set, Return Hose Assembly.
- Power and control: Drive Assembly (clutch parts, power switch, potentiometer and electronic pressure control).
- Frame and mounts: Cart Assembly, Caster Assembly, Main Assembly, Floating Gun Mount.
- Add-ons: Second Gun Kit, Line Laser, 12 Gallon Paint Hopper, Accessories Turf Kit.
The fluid section: the wear end
The Fluid Section Assembly page lists the parts that wear first on any piston striper. It includes a 0509510 Fluid Section Repacking Kit, a 0509913 Piston Rod, Packaged, a 0509914 Cylinder, a piston assembly, inlet and outlet balls and seats, an upper cage and a lower support ring.
Pressure that will not hold, or paint leaking at the pump, points here. A scored piston rod destroys new packings, so inspect the rod before you fit a kit. Inlet and outlet balls and seats cause loss of pressure or trouble priming when worn. Our diagram numbers each part so you can pick the individual piece instead of replacing the whole section.
Filter, prime/spray valve and siphon
The Filter Assembly page lists a 730-067-30 manifold filter, a bypass valve assembly, a pressure sensor assembly and the filter and bypass sensor housing. The Siphon Set page has the inlet screen. These are the parts to clean or replace if the striper spits or pulses. Clean filters after every job, and use the mesh your coating needs.
The Prime/Spray Valve page lists the relief valve knob, bypass valve seat, bypass cam base, an O-ring and a gasket. This is the valve you use when relieving pressure and priming, so the manual's procedure for your model applies before you touch it.
Drive, controls and accessories
The Drive Assembly page lists a power switch, a potentiometer assembly, an electronic pressure control assembly and clutch parts: a clutch field and a packaged clutch rotor. If pressure adjustment is erratic, the control parts are the place to look.
The accessory pages are short but useful. The Line Laser, Second Gun Kit, 12 Gallon Paint Hopper seal and Turf Kit front wheel each have their own page, and the Caster Assembly page covers the front wheel and spacer. The Cart Assembly lists the gun cable and return spring.
Where it fits
Titan markets its PowrLiner-family stripers for pavement and field marking, such as parking lots and athletic fields, and the LCX 130 is listed on our site with the same striper parts pages. Check the manual and the coating maker's tip recommendation for your job, and call (713) 931-0006 if you need help finding a part for your unit.
Wear parts listed on the LCX 130 diagram pages. Prices on the grid are live.
−16%
Bottom line
Start from the symptom: leak or pressure loss, open the Fluid Section; spitting, open the Filter Assembly; erratic pressure control, open the Drive Assembly. The accessory pages cover the second gun, laser and hopper.
Not Sure Which Part You Need?
Send us your model and serial number and we will confirm the exact part before you order. Or find it yourself in the parts diagrams.
(713) 931-0006Order by Parts Diagram