The corded FlexSpray Handheld has one diagram page, the FlexSpray HandHeld Parts List, plus an accessories page. Parts fall into four groups: gun body and air path, the front end (air cap, fluid nozzle, needle kit, seals), the cup and its seals, and the suction filters and feed tube. Match your front end colour, then order by callout number.
Which FlexSpray this guide covers
The parts below are the ones on the site's diagram for the corded FlexSpray Handheld (model 0524093). The cordless FlexSpray Pro 18V is a different machine. Do not assume a part from the corded diagram fits the Pro 18V; the site does not list Pro 18V parts on these diagram pages, so call (713) 931-0006 with your model and serial number if you own the cordless one.
Two pages hold everything. The numbered exploded view is FlexSpray HandHeld Parts List, and the loose consumables sit on FlexSpray Handheld Accessories. Both are reachable from the FlexSpray series page.
Gun body and air path
The handheld is a turbine-driven air sprayer: Titan calls the turbine JetForce, and the paint is atomized with that air at the front end. The parts that carry and control the air are on the body side of the diagram.
Body and air parts
Titan describes the handheld's turbine as replacing the pistons, cylinders and prime valves of a conventional airless pump, and states that wear parts like those are non-existent on this model. That is Titan's launch claim, not a service-life figure, so treat it as a reason the parts list is short and made of seals, filters and tips rather than pump internals.
The front end: air cap, nozzle, needle and seals
The front end is where the coating leaves the gun, and it twists off with the Quick Change System. There are two versions: the white FlexFinish for heavier coatings such as latex, enamel and acrylic, and the red FineFinish for stains, lacquers and urethanes. The needle kit is the part that depends on which one you own, so check the colour first.
Front end parts on the diagram
| Part | Callout | Part number | What to know |
|---|---|---|---|
| Air Cap | 5 | 0529909 | Directs the atomizing air at the nozzle. Clean the air holes first if the pattern is off. |
| Fluid Nozzle (Flex Finish) | 6 | 0529910 | Meters the coating on the white front end. |
| Spray Jet Kit | 4 | 0529908 | The jet components as a kit. |
| Flex Finish Needle Kit (White) | 18 | 0529245 | Needle kit for the white FlexFinish front end. |
| Fine Finish Front End Needle Kit (Red) | 18 | 0529246 | Needle kit for the red FineFinish front end. Same callout, different kit. |
| Nozzle Seal | 7 | 0529921 | Seals the nozzle to the front end. |
| Front End Assembly O-Ring | 8 | 0529922 | Seals the front end where it twists onto the gun. |
| Flex Finish Front End (White) | n/a | 0529009 | The whole white front end, listed on the accessories page. |
Part numbers and callouts are from the site's FlexSpray HandHeld Parts List and Accessories pages.
The two needle kits share callout 18 on the diagram, which is an easy place to order the wrong one. Match the kit colour to your front end: 0529245 for white, 0529246 for red.
The cup, lid and seals
The coating sits in a one-quart container on the gun. Titan lists the container, a gasket pack and a threaded lid seal as separate parts, so a leaking lid does not mean a new cup.
- 0529925 Material Container (1 Qt), callout 12.
- 0529923 Container Seal (5PK Gasket), callout 10. Replaces the gasket, and you get five.
- 0529927 Threaded Lid and Container Seal, on the accessories page.
- 0529924 Plastic Cup, on the accessories page.
Feed tube and suction filters
Material reaches the front end through a feed tube with a filter on the suction end. Two filters are listed: 0529916 Fine Suction Tube Filter and 0529915 Coarse Suction Tube Filter (5pk). The feed tube is 2319222A. Which grade suits which coating is not something we can state here, so start with the one that came on your gun and call us if you want to change it.
Titan's manual lists a clogged or loose suction tube among the causes of little or no flow. So when the gun delivers nothing, check the feed tube connection and the suction filter before you look at anything on the front end.
What to order first
Identify the front end
White is FlexFinish, red is FineFinish. This decides the needle kit.
Rule out the cheap items
Clean the nozzle and air holes. Titan's manual says never to clean the nozzle or air holes with sharp metal objects. The 0529411 Cleaning Brush is on the diagram for that job.
Replace seals and filters by symptom
Leak at the lid points to the container seals. Leak where the front end meets the gun points to the O-ring or nozzle seal. Weak delivery points to the suction filter and feed tube, then the air filter.
Order by callout
Open the parts list, find the callout and add the part. If the part you need is not on the page, call (713) 931-0006.
These are the parts most owners reach for first. Prices and availability show live in the grid.
The numbered exploded view with callouts.
Needle kits, filters, feed tube and container seals.
FlexSpray manuals for cleaning and reassembly.
Bottom line
The corded FlexSpray Handheld parts list is short: body, front end, container and filters. Identify your front end colour, find the callout on the diagram, and order that part. For fitment doubts, call (713) 931-0006 with your model and serial number.
Not Sure Which Part You Need?
Send us your model and serial number and we will confirm the exact part before you order. Or find it yourself in the parts diagrams.
(713) 931-0006Order by Parts Diagram