C.A. Tech CP-L100H Spray Gun
C.A. TECHNOLOGIES LYNX 100H LOW-CFM HVLP SMART PACK
C.A. Technologies CP-L100H Lynx 100H HVLP Smart Pack combines an industrial pressure-feed spray gun with 0.8, 1.3, and 1.7 mm fluid nozzles, two low-CFM air caps, service tools, and a protective case for versatile professional finishing.
CP-L100H is manufactured by C.A. Technologies, not Titan Tool. The Lynx 100H uses stainless-steel fluid passages and interchangeable air caps, including low-CFM configurations suitable for smaller compressors. This Smart Pack does not include a pressure cup; connect it to a compatible pressurized fluid supply.
C.A. TECHNOLOGIES LYNX 100H LOW-CFM HVLP SMART PACK
C.A. Technologies CP-L100H Lynx 100H HVLP Smart Pack
Expand professional finishing capability with C.A. Technologies CP-L100H, a Lynx 100H pressure-feed HVLP Smart Pack combining three fluid nozzles, two low-CFM air caps, service tools, and a protective case for spraying materials ranging from stains and dyes to topcoats and primers.
| Detail | Technical / Commercial Information |
|---|---|
| Product Overview | CP-L100H is the Smart Pack version of the C.A. Technologies Lynx 100H industrial low-CFM HVLP pressure-feed spray gun. The verified CAT Pack configuration uses three standard fluid nozzle sizes—0.8, 1.3 and 1.7 mm—plus two standard air caps, service tools and a protective carrying case. The CP-L100H Smart Pack is supplied without a pressure cup. |
| Function | A pressurized cup or pressure tank supplies coating through the gun's 3/8-inch NPS male fluid inlet while compressed air enters through the 1/4-inch NPS male air inlet. The selected air cap atomizes the coating under HVLP operating conditions. Material output is controlled primarily through correct fluid-orifice selection and fluid-supply pressure, with the gun's fluid control limiting needle travel when required. |
| Industrial Applications | The Lynx 100H is designed for general-purpose industrial, wood and automotive finishing. C.A. Technologies specifically identifies low-CFM configurations for dyes, spray stains, topcoats and primers. With appropriate optional air-cap and nozzle combinations, the platform can also atomize higher-solids materials. Stainless-steel fluid passages support both solvent-based and water-based finishing materials when otherwise compatible with the coating system. |
| Accurate Compatible Titan Machines | CP-L100H is C.A. Technologies equipment rather than a Titan-manufactured replacement spray gun. Titan literature has distributed C.A. Technologies spray equipment, but no model-specific Titan airless or turbine sprayer fitment is established for this Smart Pack. The L100H requires regulated compressed air and an independent pressurized fluid source such as a compatible pressure cup or pressure tank. |
| Accurate Part Number | C.A. Technologies CP-L100H. This is the no-cup Smart Pack built around the Lynx L100H pressure-feed HVLP spray gun. Related but distinct packages include CP-L100H-303R2 with a regulated 1-quart aluminum pressure cup and CP-L100H-PPSR2 with a regulated PPS pressure-cup system. |
| Compatible Parts & Assemblies | The standard CAT Pack selections documented for the L100H include 31-0208 0.8 mm, 31-0213 1.3 mm and 31-0217 1.7 mm fluid nozzles with the common 40-1100 needle. Standard air caps include 21-1091 at approximately 8 SCFM / 15 PSI maximum HVLP inlet pressure and 21-1094 at approximately 13 SCFM / 33 PSI. The gun uses 21-1001 air-cap ring and 60-1502 #2 fan control. |
| Related Parts Commonly Serviced Together | Inspect the fluid nozzle, 40-1100 needle and installed air cap together whenever atomization, pattern consistency or fluid shutoff changes. Related service points include the 21-1001 air-cap ring, 60-1502 fan control, needle packing, air valve, trigger and fluid-control components. C.A. Technologies identifies repair kit 10-106 for the Lynx L100H. |
| Common Problems Solved | The Lynx 100H addresses applications where professional HVLP performance is required but available compressor capacity may be limited. Its interchangeable air caps range from approximately 6 to 22.5 SCFM depending on configuration. Multiple fluid nozzles allow the same gun platform to handle substantially different coating viscosities instead of forcing one nozzle to cover every material. |
| Use with Coating Systems | Connect the gun to clean, dry and regulated compressed air plus a compatible pressurized material supply. Air requirements depend on the installed cap: the L100H family ranges from the 21-1090 at approximately 6 SCFM and 15 PSI maximum HVLP inlet pressure through higher-output caps requiring up to approximately 22.5 SCFM. Select fluid nozzle, air cap and fluid pressure according to coating viscosity and desired production rate. |
| OEM & Brand Information | CP-L100H is manufactured by C.A. Technologies, not Titan Tool. The Lynx 100H features stainless-steel fluid passages, rugged lightweight construction, 1/4-inch NPS male air inlet and 3/8-inch NPS male fluid inlet. The gun weighs approximately 20 ounces. C.A. Technologies specifies that air consumption depends on the air cap installed. |
| Commercial Benefits | The Smart Pack gives contractors and finishing shops a configurable professional HVLP gun without forcing purchase of another pressure cup when a suitable material supply is already available. Three standard nozzle sizes, two air caps, stainless-steel fluid passages and low-CFM options make the L100H useful for mobile finishing, small shops and production environments requiring coating flexibility. |
Contractor Selection Insight
Choose CP-L100H when you already have a compatible pressure cup or pressure tank and want the Lynx 100H's broad setup flexibility without buying another material container. For maximum portability, C.A. Technologies offers a 21-1090 configuration requiring approximately 6 SCFM at 15 PSI; however, the Smart Pack's different air caps have different airflow requirements. Always size the compressor to the air cap actually installed.
FAQ Section
Key answers for professionals selecting the CP-L100H Lynx 100H Smart Pack.
No reviews yet. Be the first to review this product!