The Titan Elite 2000 (2437317) is a compact electric PermaStroke sprayer. Titan lists 3000 psi, 0.47 GPM, a 0.021" maximum tip and 50-100 gallons a week, with a 1.0 HP DCX motor. The site lists its inlet and outlet valves, suction filter, pressure relief valve and hopper by part number.
The Elite 2000 is one of the electric Elite sprayers on Titan's list, alongside the Elite 3000 and the battery-powered Elite 3500 72V. It is aimed at residential, light commercial and fine-finish work. Published sources disagree on a few of its figures, including pressure and weight, so this page gives only what Titan lists and says plainly what is left out.
Elite 2000 at a glance
Titan Elite 2000 (2437317), as Titan lists it
| Item | Titan lists |
|---|---|
| Power | Electric, 1.0 HP DCX motor |
| Max operating pressure | 3000 psi |
| Max delivery | 0.47 GPM |
| Max tip, one gun | 0.021" |
| Recommended gallons per week | 50-100 |
| Supplied with the unit | RX-80 gun, 517 tip, 1/4" x 50' airless hose |
Pressure is 3000 psi per Titan, not the 3300 psi of the Elite 3000. Weight is left out because published figures disagree.
Look at the pressure line before you compare it with other Elites. A 3300 psi figure on some dealer pages is not Titan's number for this model. Titan also says PermaStroke Technology delivers top performance between 300 and 3000 psi on the 2000, rather than 300 to 3300 psi on its larger siblings. As with the other Elites, Titan describes a sealed hydraulic design with no piston, packings, cylinder or clutch to wear or burn out.
Fine finish and residential work
Titan describes the Elite 2000 as suited to all standard architectural primers, paints and coatings, in residential, light commercial and fine-finish applications. The 0.021" tip ceiling is what makes the fine-finish side possible. Titan describes that small maximum as versatility for fine finish work and traditional applications alike.
The tip works as a limit as well as a feature. A smaller orifice delivers less material, so a thick coating that needs a larger tip is not what this sprayer is built around, and Titan's 0.47 GPM flow is below the 0.60 GPM it lists for the Elite 3000. If you often spray heavy-bodied coatings, compare the tip sizes your coating needs with the maximum above before buying. For anything unusual, check the manual for your coating.
Frame and siphon
Titan lists a skid frame for the 2000 and a flexible siphon that works with 1 or 5-gallon containers. That is a small, portable layout: you carry the machine, set the container beside it and spray. The site also lists a 3.7 liter hopper assembly, 2463293, for the 2000 if you want to feed it from a hopper instead of a pail.
The two wear parts
Titan says the Elite 2000 is field serviceable with only two wear parts to change. On the site, the two parts that fit that description are the valves: 2443943 Inlet Valve and 2443904 Outlet Valve. Titan does not publish a service life for either, so there is no hours or gallons figure here. As on any airless sprayer, a worn or dirty valve shows up as pulsing, loss of pressure or a pump that will not prime.
Check the cheaper things first. A partly blocked filter or tip causes the same symptoms, so clean the suction filter and the tip before ordering a valve, and flush the sprayer after every job so paint does not dry inside it.
Parts the site lists for the Elite 2000
Elite 2000 parts on the site
All eight are listed on the site with the Elite 2000 named in their fitment. They are not on a diagram page, because the Elite 2000 does not have one here. There is no callout to follow, so order by part number and read the product page. The Titan Elite sprayer parts page links the Elite families that do have diagrams, and the Elite 3000 accessories page shows the guns, hoses, tip guards and filters Titan lists around that sprayer. Those accessories are not labeled for the 2000, so confirm fitment before you order any of them for one.
Manual and fitment
The manual is where the pressure relief procedure, flushing and troubleshooting for your model are written, and you should have it open before you service the pump. Titan manuals are collected on our manuals page. If a part is not obvious from its name, phone (713) 931-0006 with the model and serial number and what the sprayer is doing.
Elite 2000 parts listed on the site:
The Short Version
The Elite 2000 is a small electric sprayer for fine finish and light work: 3000 psi, 0.47 GPM, 0.021" tip, 50-100 gallons a week. Its two wear parts are the inlet and outlet valves, 2443943 and 2443904, and the rest of its listed parts are filters, a relief valve, a hopper and covers. Order by part number from the product pages.
Not sure which Elite 2000 part you need?
Call (713) 931-0006 with your model and serial number and our parts team will confirm the part before you order.
(713) 931-0006Order by Parts Diagram