Titan 697-427 TR1 427 Line Striping Tip
TITAN TR1 REVERSIBLE LINE STRIPING TIP
Titan 697-427 TR1 427 Line Striping Tip combines a 4-inch nominal stripe with a .027-inch orifice for higher-output professional marking. Its reversible airless design supports consistent line width, sharp edges, uniform film build, and efficient production.
Titan lists approximately 0.78 GPM / 2.95 LPM reference flow for the .027-inch orifice. Select this larger-orifice 4-inch TR1 when the coating and PowrLiner capacity require greater material delivery than smaller 4-inch tip sizes.
| Detail | Technical / Commercial Information |
|---|---|
| Product Overview | Titan 697-427 is a TR1 reversible line-striping spray tip. Titan's official TR1 chart specifies a 4-inch / 102 mm nominal fan-pattern width and .027-inch orifice. The .027-inch size carries approximately 0.78 GPM / 2.95 LPM reference flow, with the TR1 line-striping tip family rated to 5,000 PSI / 34.5 MPa maximum working pressure. |
| Function | The .027-inch orifice meters a comparatively high volume of coating while the tip geometry forms a 4-inch nominal stripe. Titan explains that, at the same fan width, increasing orifice size applies a greater volume of paint to the area. The reversible configuration also helps operators clear certain tip obstructions. |
| Industrial Applications | Designed for professional pavement, traffic, parking, industrial, facility, and field-marking applications where a 4-inch nominal stripe and relatively high material delivery are required. Final suitability depends on the specified coating, desired film build, application speed, and capacity of the line-striping machine. |
| Accurate Compatible Titan Machines | 697-427 belongs to Titan's TR1 tip system used with professional PowrLiner line-striping equipment. Because a .027-inch tip requires significantly more output than smaller TR1 sizes, compatibility must be determined from the specific PowrLiner's maximum tip rating and number of guns being operated. Do not assume every PowrLiner supports this orifice size. |
| Accurate Part Number | Titan 697-427 — TR1 427 Line Striping Tip. In Titan's tip-numbering system, the first digit identifies the approximate stripe width when sprayed 6 inches from the surface, while the final two digits identify the orifice in thousandths of an inch. Therefore, 427 identifies a 4-inch stripe with a .027-inch orifice. |
| Compatible Parts & Assemblies | Use with a compatible Titan airless line-striping gun, reversible-tip guard, tip seal, suitable gun filtration, high-pressure hose, and PowrLiner fluid-delivery system capable of supporting a .027-inch orifice. Titan TR1 tips are designed for Titan spray-gun guards and most other industry spray-gun guards. |
| Related Parts Commonly Serviced Together | Inspect the tip guard, tip seal, spray-gun filter, gun fluid passages, high-pressure hose, pump filtration, and gun-positioning hardware when diagnosing poor stripe quality. Restricted material flow, worn seals, incorrect gun height, or insufficient pump output can affect atomization and fan-pattern performance. |
| Common Problems Solved | Replacing a worn 697-427 can help restore the intended fan pattern, line-edge definition, and material control when normal abrasive wear enlarges an existing tip. The larger .027-inch opening also addresses applications requiring greater coating delivery than smaller 4-inch-pattern TR1 tips can provide, when supported by the coating and sprayer. |
| Use with Coating Systems | Select 697-427 only when the coating manufacturer and line-striper specifications support a .027-inch airless tip. Titan recommends selecting TR1 tips by both fan width and orifice size: lighter-viscosity fluids generally use smaller openings, while heavier-viscosity materials generally require larger openings for proper atomization. |
| OEM & Brand Information | 697-427 is a genuine Titan Tool TR1 line-striping tip. Titan describes TR1 tips as engineered to provide sharp line edges, consistent line width, and uniform film thickness while helping reduce wasted paint. Titan specifies a maximum working pressure of 5,000 PSI / 34.5 MPa for the line-striping tip family. |
| Commercial Benefits | The 427 configuration combines the widely used 4-inch nominal striping pattern with a high-output .027-inch opening. Compared with smaller 4-inch TR1 sizes, it can deliver substantially more coating to the same general stripe area, making it useful for properly matched higher-volume marking applications while retaining Titan's reversible-tip convenience. |
Contractor Selection Insight
Choose Titan 697-427 when you need a 4-inch nominal stripe and the coating requires the greater delivery of a .027-inch orifice. Titan lists approximately 0.78 GPM / 2.95 LPM reference flow for this opening. That is substantially higher than smaller 4-inch TR1 options, so verify both coating requirements and your PowrLiner's maximum tip capacity before ordering. A larger orifice should be selected for material demand, not simply to increase production speed.
FAQ Section
Key answers for contractors selecting Titan 697-427 TR1.
No reviews yet. Be the first to review this product!
